BenchReference

7/16″-14 UNC Thread

Recommended tap drill U
Tap drill Ø 0.3680″ / 9.347 mm
Major Ø 0.4375″ / 11.112 mm
Threads per inch 14

The chart recommendation gives approximately 74.9% thread engagement — the conventional target for average materials. It is not the only valid choice; see the options below.

Specification

Designation7/16″-14 UNC
Thread familyUnified National Coarse (UNC)
Nominal size7/16
Basic major diameter 0.4375″ / 11.112 mm
Threads per inch / pitch14 TPI (1.814 mm pitch)
Recommended tap drill U (0.3680″ / 9.347 mm)
P = 0.0714″ (14 TPI) 60° major Ø 0.4375″ 60° thread form (UN / ISO) — schematic

Tap drill options by thread engagement

Any of these standard drills produces a usable engagement for 7/16″-14 UNC; smaller drills give stronger threads but higher tapping torque. Percentages use the conventional approximation (60° thread form).

23/64″ 84.2% U ★ 74.9% 9.6 mm 64.2% shaded = share of the full thread height the tap forms · accent line = drilled hole wall
★ = chart recommendation. A smaller drill leaves more of the thread height for the tap to form.
Drill Decimal in mm Approx. engagement
23/64″ 0.3594 9.128 84.2%
9.2 mm 0.3622 9.2 81.1%
9.3 mm 0.3661 9.3 76.9%
U — chart recommendation 0.3680 9.347 74.9%
9.4 mm 0.3701 9.4 72.7%
9.5 mm 0.3740 9.5 68.4%
3/8″ 0.3750 9.525 67.4%
V 0.3770 9.576 65.2%
9.6 mm 0.3780 9.6 64.2%

Nearest drills to the tap drill in other systems

Drill Size vs U Resulting engagement
9.3 mm 0.3661″ / 9.3 mm −0.047 mm 76.9%
3/8″ 0.3750″ / 9.525 mm +0.178 mm 67.4%

Clearance holes

For a bolt or screw of this size to pass through freely. Recommended drills per ASME B18.2.8: close, normal, and loose fits.

Tapped hole Clearance hole U tap drill threads cut into the material 15/32" (normal fit) the tinted gap lets the bolt pass freely
Schematic — proportions exaggerated for clarity; use the table values.
Fit Drill / Ø Decimal in mm
close 29/64″ 0.4531 11.509
normal 15/32″ 0.4688 11.906
loose 31/64″ 0.4844 12.303

Hex bolt & nut dimensions

For a standard hex cap screw (ASME B18.2.1) and finished hex nut (ASME B18.2.2) in this size.

Wrench / socket size (bolt head) 5/8″
Wrench / socket size (nut) 11/16″
Head height 9/32″ (0.2813″)
Nut thickness 3/8″ (0.3750″)
Compatible nut 7/16-14 hex nut
Head — top view Bolt — side view Nut — side view width across flats = 5/8″ wrench head height 9/32″ thickness 3/8″

Basic (nominal) dimensions. See the wrench & socket size charts for all sizes and the metric ↔ SAE socket comparison.

Related threads

Data provenance. ASME B1.1, Unified Inch Screw Threads (ASME). Machinery’s Handbook — tap drill charts (Industrial Press). ASME B18.2.8, Clearance Holes for Bolts, Screws, and Studs (ASME). ASME B18.2.1, Hex Cap Screws (head dimensions) (ASME). ASME B18.2.2, Finished Hex Nuts (ASME). Engagement percentages use the conventional approximation (engagement = (major − drill) ÷ (1.29904 × pitch)) and are guidance, not a tolerance specification. See all data sources.